Provide Valid 300-425 Dumps To Help You Prepare For Designing Cisco Enterprise Wireless Networks Exam Mar 19, 2026
Cisco 300-425 Dumps Questions [2026] Pass for 300-425 Exam
NEW QUESTION # 94
A customer asks an engineer to explain the concept of mobility domains and mobility groups. Which statement does the engineer respond with?
- A. WLCs do not need to be in the same mobility domain to communicate with each other. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.
- B. If WLCs are in the same mobility domain, they communicate with each other but, if an anchor WLC is present, it must be in the same mobility domain for communication to be possible.
- C. If WLCs are in the same mobility domain, they communicate with each other. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.
- D. A mobility group does not constrain the distribution of security context of a client and also does not constrain AP fail-over between controllers when the WLC are in the same mobility domain.
Answer: C
Explanation:
Section: Mobility
NEW QUESTION # 95
During a post deployment site survey, issues are found with non-Wi-Fi interference.
What should the engineer use to identify the source of the interference?
- A. network analysis module
- B. wireless intrusion prevention
- C. Cisco Spectrum Expert
- D. Wireshark
Answer: C
Explanation:
https://www.cisco.com/c/en/us/products/collateral/wireless/spectrumexpert/product_data_sheet09
00aecd807033c3.html
NEW QUESTION # 96
An engineer is performing an AP-on-a-stick survey and finds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements. Which two actions during the survey reduce channel overlap? (Choose two.)
- A. Use directional antennas to limit the coverage area of some APs.
- B. Raise the minimum data rate to 24 Mbps.
- C. Allow the use of UNII-2e channels.
- D. Increase AP transmit power to improve the SNR.
- E. Enable power saving mode.
Answer: A,E
NEW QUESTION # 97
An engineer is upgrading the legacy access points to 802.11ac Wave 2 capable access points.
The existing gigabit uplinked switches provide 802.3at. Which switch limitation is a concern?
- A. collision domains
- B. interface throughput
- C. high availability
- D. output power
Answer: B
Explanation:
As the wave 2 Aps need 802.11at, the switches looks fine. Wave2 Aps support multigigabit, then the throughput.
NEW QUESTION # 98
Guest anchoring is configured for a newly created SSID for your company. It has been noticed that the mobility tunnels are not up, and that MPING fails from your foreign WLC to the anchor WLC. What is the reason that it is failing?
- A. A rule is needed at the firewall to allow TCP port 16666 for communication to work.
- B. A rule is needed at the firewall to allow UDP port 97 for communication to work.
- C. A rule is needed at the firewall to allow TCP port 97 for communication to work.
- D. A rule is needed at the firewall to allow UDP port 16666 for communication to work.
Answer: D
Explanation:
NEW QUESTION # 99
An engineer must perform a predictive design for a wireless network for location readiness and to mitigate interference. Which power level does the engineer use?
- A. 50 mw
- B. 10 mw
- C. 18 mw
- D. 20 mw
Answer: C
NEW QUESTION # 100
Which statement about creating a mobility group is true, excluding mobility anchors?
- A. Each WLC must use the same mobility name and be defined as a peer in each other's static mobility members list.
- B. The WLCs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions.
- C. If WLCs with HA SSO are deployed, each WLC in the WLC HA pair considered separately as a mobility peer.
- D. A mobility groups does not require all WLCs in the group to use the same virtual IP address.
Answer: C
Explanation:
NEW QUESTION # 101
Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?
- A. ping
- B. mping
- C. rping
- D. eping
Answer: D
Explanation:
The 'eping' command is used on Cisco Wireless LAN Controllers to verify that the redundancy peer in a Stateful Switchover (SSO) pair of controllers is up and connected. This command sends ECHO packets to the peer controller to ensure connectivity.
NEW QUESTION # 102
An architect configures a set of AirOS controllers to be in the same mobility group as the existing controllers. The implementation should facilitate inter-controller roaming for users in their new campus. After the configuration, the mobility tunnel is not operational for the data path in the network. Which two validations should be performed? (Choose two.)
- A. mapping
- B. mepping
- C. firewall port 16666
- D. rping
- E. firewall IP protocol 97
Answer: C,E
Explanation:
When the mobility tunnel is not operational for the data path, it is essential to validate the network's firewall settings. Firewall port 16666 must be open to allow mobility control messages to pass through, and firewall IP protocol 97 (EtherIP) must be permitted to enable the encapsulation of IP within IP, which is necessary for the data path of the mobility tunnel. Ensuring these firewall settings are correctly configured is critical for facilitating inter-controller roaming and operational mobility tunnels.
NEW QUESTION # 103
An AP is receiving 802.11 packets on its 802.11a radio with an RSSI value of -77 dBm. The current AP is part of an AP group that has been assigned an RF profile with RX-SOP set to Medium for 802.11a. Which action does the AP take with the packets?
- A. Frames are decoded by the 2.4 GHz radio.
- B. All frames are classified as non-Wi-Fi frames and are not decoded by the 2.4 GHz radio.
- C. All frames are classified as non-Wi-Fi frames and are not decoded by the 5 GHz radio.
- D. Frames are decoded by the 5 GHz radio.
Answer: D
Explanation:
An RSSI value of -77 dBm is within the range that a 5 GHz radio can receive and decode, provided it's not below the RX-SOP threshold set for the RF profile. Since the RF profile is set to Medium for 802.11a, which operates in the 5 GHz band, the AP's 5 GHz radio will decode the frames.
NEW QUESTION # 104
A network engineer is designing a new wireless network. The network needs to have these characteristics:
Which approach should be taken?
- A. Deploy APs near each other for 2.4 GHz coverage, and disable the 5 GHz radios for all APs.
- B. Deploy APs near each other for 2.4 GHz coverage, and disable the 5 GHz radios for some APs.
- C. Deploy APs near each other for 5 GHz coverage, and disable the 2A GHz radios for some Aps.
- D. Deploy APs near each other for 5 GHz coverage, and enable the 2.4 GHz radios for all Aps.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/86/b_Cisco_Wireless_LAN_Controller_Con
NEW QUESTION # 105
What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?
- A. 50%
- B. 20%
- C. 40%
- D. 30%
Answer: B
Explanation:
NEW QUESTION # 106
A university is in the process of designing a wireless network in an auditorium that seats 500 students and supports student laptops. Which design methodology should the university implement in the auditorium?
- A. voice design model
- B. location design model
- C. roaming design model
- D. high-density design model
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/dam/en_us/solutions/industries/docs/education/cisco_wlan_design_guide.pdf
NEW QUESTION # 107
An engineer is designing a network deployment for a college with six buildings Each building must have a WLC located in the IDF to support the APs. The wireless clients should be able to roam between the APs and the controllers. Which type of wireless architecture should be used?
- A. Centralized
- B. Autonomous
- C. Cloud
- D. Distributed
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob41dg/emob41dg-wrapper/ch2_A
NEW QUESTION # 108
A customer is deploying an 802.11ac network on a oor to support approximately 300 wireless devices. Which setting must be changed on Cisco Prime Infrastructure Planning Tool to predict the number of APs the customer needs to service the new oor?
- A. 802.11n Protocol Support
- B. Data Coverage Support Margin
- C. Add AP Field
- D. Demand Settings
Answer: D
NEW QUESTION # 109
How are mobility groups created, excluding mobility anchors?
- A. If WLCs with HA SSO are deployed, each WLC in the WLC HA pair is considered separately as a mobility peer.
- B. Each WLC must use the same mobility domain name and be defined as a peer in each other' s static mobility members list.
- C. The WLGs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions.
- D. A mobility group does not require ell WLCs in the group lo use the same virtual IP address.
Answer: A
NEW QUESTION # 110
A network engineer is working on a design for a wireless network that must support data, voice, and location services. To support these services, which access point placement must the engineer use?
- A. perimeter and corner
- B. perimeter only
- C. indoor and outdoor
- D. corner only
Answer: A
Explanation:
NEW QUESTION # 111
A company has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity, 5 access points are set to high failover priority and 7 access points are set to critical failover priority.
During a failure, not all critical access points failed over to the backup Cisco WLC.
Which configuration is the cause of this issue?
- A. The critical priority access point count is oversubscribed.
- B. network ap-priority is set to enable.
- C. The high priority access point is oversubscribed.
- D. network ap-priority is set to disable.
Answer: D
Explanation:
NEW QUESTION # 112
A wireless engineer is getting ready to perform a predictive site survey. The new network needs to support data and voice over wireless. Which two Cisco recommendations should be considered for the design? (Choose two.)
- A. Set the cell overlap to 15%
- B. Use the 5 GHz radio band due to 40 MHz bandwidth capability.
- C. Set -19 dBm of separation between APs on the same channel.
- D. Set the cell boundary to -67 dBm.
- E. Use the 5 GHz radio band due to the 24 non-overlapping channels.
Answer: B,D
Explanation:
The 5 GHz band is recommended for voice over wireless due to its wider channel bandwidths, allowing for higher data rates. Setting the cell boundary at -67 dBm ensures sufficient signal strength for reliable voice communication. Reference: CCNP Enterprise Wireless Design ENWLSD 300-425 Official Cert Guide.
NEW QUESTION # 113
An engineer in a branch office that does not have a wired backhaul must ensure that local clients can be switched locally and authenticated centrally. In which mode must the AP be configured?
- A. Cisco FlexConnect
- B. RAP
- C. MAP
- D. Flex+Bridge
Answer: A
Explanation:
Cisco FlexConnect mode is designed for branch offices that lack a wired backhaul. It allows APs to switch client data traffic locally while still performing client authentication centrally. This mode provides the flexibility needed for branch deployments, ensuring that client traffic is handled efficiently even if the WAN link to the central site is down. Reference: Cisco FlexConnect technical documentation and Designing Cisco Enterprise Wireless Networks (ENWLSD) training.
NEW QUESTION # 114
When conducting a site survey for real-time traffic over wireless, which two design capabilities of smartphones and tablets must be considered? (Choose two.)
- A. fewer antennas than laptops
- B. no support for 802.11r
- C. higher data rates than laptops
- D. lower data rates than laptops
- E. no support for 802.11ac
Answer: A,D
Explanation:
NEW QUESTION # 115
......
Cisco 300-425 exam is an integral part of the Cisco Certified Design Expert (CCDE) track. The CCDE certification is a highly respected credential in the IT industry, and passing the 300-425 exam is one of the requirements to earn this certification. 300-425 exam is a challenging test of knowledge and skills, and it requires a deep understanding of wireless networking concepts and technologies.
Achieve Success in Actual 300-425 Exam 300-425 Exam Dumps: https://www.real4dumps.com/300-425_examcollection.html
Updated Cisco Study Guide 300-425 Dumps Questions: https://drive.google.com/open?id=14zAFS0HYTzgLTNlP3DJp8Y99RksrQheT
