2021 Updated Verified Pass NACE-CIP1-001 Exam - Real Questions & Answers
Dumps Moneyack Guarantee - NACE-CIP1-001 Dumps Approved Dumps
NEW QUESTION 18
Which of these tests uses a syringe?
- A. Potassium ferricyanide
- B. Sleeve test
- C. Soluble salts meter
- D. Bresle patch
Answer: D
NEW QUESTION 19
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To promote faster cure
- C. To dissolve the resin
- D. To control the evaporation rate
Answer: D
NEW QUESTION 20
Conventional spray is a good choice when:
- A. High production rates are required
- B. High quality finishes are required
- C. High transfer efficiency is required
- D. High viscosity coatings are being applied
Answer: B
NEW QUESTION 21
ASTM Standards are applicable:
- A. In North America
- B. In Asia
- C. In the USA
- D. When specified
Answer: D
NEW QUESTION 22
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Always handwritten
- C. Timely, accurate and concise
- D. Submitted before the end of the job
Answer: C
NEW QUESTION 23
Solvents are added to coating formulations to
- A. provide color.
- B. dissolve binders and form liquid coatings.
- C. decrease film permeability.
- D. increase film permeability.
Answer: B
NEW QUESTION 24
Corrosion generally occurs at which of the following sites:
- A. Electrolyte
- B. Cathode
- C. Anode
- D. Metallic pathway
Answer: C
NEW QUESTION 25
SSPC SP 1 identifies the use of:
- A. Biodegradable detergents
- B. Organic solvents
- C. Inorganic solvents
- D. A wide variety of materials
Answer: D
NEW QUESTION 26
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Advise the prospective employer that you cannot accept the position
- B. Review the NACE Attestation prior to making a decision
- C. Meet with the prospective employer to determine the scope of your role
- D. Accept the assignment without hesitation
Answer: C
NEW QUESTION 27
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Cathode
- C. Anode
- D. Reference Cell
Answer: D
NEW QUESTION 28
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Relative Humidity
- C. High Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION 29
The least effective method of surface cleaning is most likely
- A. water blasting.
- B. hand tool cleaning.
- C. dry grit blasting.
- D. power tool cleaning.
Answer: B
NEW QUESTION 30
According to SSPC PA 2 a Spot Measurement is:
- A. The average of all spot measurements in a given area
- B. A single gauge reading
- C. The average of gauge readings taken in a 4cm (1.5 inch) circle
- D. The overall average of all readings
Answer: C
NEW QUESTION 31
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks and just record the same readings as you have been getting
- B. Keep doing the checks and consult the Owner's representative for direction
- C. Keep doing the checks regardless
- D. Skip the checks as you are. confident the blast pressure is OK
Answer: B
NEW QUESTION 32
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. cracking.
- B. checking.
- C. holiday.
- D. sagging.
Answer: C
NEW QUESTION 33
Which one of the following documents is the best source for coating technical data:
- A. Specification
- B. Application Guidelines
- C. Technical Data Sheet
- D. Safety Data Sheet;
Answer: C
NEW QUESTION 34
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. soluble chemical salts
- B. sulfates
- C. inhibitor residues
- D. grease and oil
Answer: D
NEW QUESTION 35
Whenever dissimilar metals must join, the most common practice is to
- A. coat all connected dissimilar metals.
- B. provide cathodic protection to prevent corrosion,
- C. avoid coating all connected dissimilar metals.
- D. provide anodic protection to prevent corrosion.
Answer: A
NEW QUESTION 36
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to saturation level.
Answer: D
NEW QUESTION 37
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Applied in very' thin films
- C. Used strictly in immersion service
- D. Applied in very thick films
Answer: B
NEW QUESTION 38
ISO SA 2.5 is defined as:
- A. Very Thorough Blast Cleaning
- B. Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Light Blast Cleaning
Answer: A
NEW QUESTION 39
......
Updated PDF (New 2021) Actual NACE NACE-CIP1-001 Exam Questions: https://www.real4dumps.com/NACE-CIP1-001_examcollection.html
Verified NACE-CIP1-001 Exam Dumps PDF [2021] Access using Real4dumps: https://drive.google.com/open?id=14cBaRoKFfE9IjNwuBEBo7EDe76lrRoBA
